新闻资讯

木屑烘干机主轴断裂原因及解决方案!

2019-06-11 来源:http://www.zhongyanjixie.com 发布人:admin 浏览量:
[导读]:  木材干燥机主轴断裂原因:  Causes of fracture of wood dryer spindle:  木材干燥机在干燥某些物料时,容易产生一些腐蚀性气
  木材干燥机主轴断裂原因:
  Causes of fracture of wood dryer spindle:
  木材干燥机在干燥某些物料时,容易产生一些腐蚀性气体,腐蚀木材干燥机的金属部件。例如:当竹刨花板的干燥,因为竹刨花板暴露于户外堆积很长一段时间,其水分含量很高,一些生产企业,采用热油温的方法是增加加快干燥的干燥机竹刨花板,或一端的导热油,另一边吹热空气进入空心主轴转子干燥机。的高温导热油的一端有一个主传动,在高温下,容易变形,而且携带整个传输系统的低速高扭矩、轴是非常容易变形,抗压力和疲劳的成都不均匀现象,另一边的空心轴,气体腐蚀,但这些因素的主轴断裂的主要原因。
  When wood dryer dries some materials, it is easy to produce some corrosive gases, which corrode the metal parts of wood dryer. For example, when bamboo particleboard is dried, because bamboo particleboard is exposed to outdoor accumulation for a long time, its moisture content is very high. Some manufacturers adopt the method of hot oil temperature to increase the bamboo particleboard drier, or the heat conducting oil at one end, while blowing hot air into the hollow spindle rotor dryer. One end of the high temperature heat conducting oil has a main drive, which is easy to deform at high temperature. The low speed and high torque of the transmission system and the shaft are very easy to deform. The pressure resistance and fatigue are not uniform. The hollow shaft on the other side is corroded by gas, but the main reason for the fracture of the spindle is that these factors are not uniform.
  木材干燥机主轴断裂解决方案:
  Wood dryer spindle fracture solutions:
  为了解决主轴断裂的问题,不仅在平时的生产工作中,严格按照烘干机的操作说明,不能做一些违法操作,从而影响了木材烘干机的使用寿命。此外,我们需要从以下两点进行改进。
  In order to solve the problem of spindle fracture, not only in the normal production work, strictly according to the operation instructions of the dryer, can not do some illegal operations, thus affecting the service life of the wood dryer. In addition, we need to improve from the following two points.
木屑烘干机厂家
  1. 对于有腐蚀性气体的干燥物料,主轴表面应覆盖一层密封不锈钢,以隔离从主轴蒸发的腐蚀性气体。
  1. For dry materials with corrosive gases, the surface of the spindle should be covered with a sealed stainless steel to isolate the corrosive gases evaporated from the spindle.
  2. 针对主轴变形应力不均匀的问题,建议将主轴同一端部进出导热油的方式改为一端进、一端出。保持变形应力均匀。
  2. In view of the uneven deformation stress of the spindle, it is suggested that the way of entering and leaving the heat conducting oil at the same end of the spindle should be changed to one end entering and one end leaving. Maintain uniform deformation stress.
  3、增加烘干机转子导热管的数量,降低导热油的温度,从而改善主轴的工作环境。
  3. Increase the number of heat-conducting tubes in the rotor of dryer and reduce the temperature of heat-conducting oil, so as to improve the working environment of the spindle.
返回顶部

版权所有©山东众焱机械有限公司 备案号:鲁ICP备19005667号-1 服务热线:18005415007 流量统计: