新闻资讯

沙子烘干机的通风量怎么调试?

2019-04-17 来源:http://www.zhongyanjixie.com 发布人:admin 浏览量:
  保证沙子烘干机的通风量,随时掌握烘干机内温度,并依此进行燃料的添加才能达到节能烘干状态。沙子烘干机通风处,主要是在烘干机烘干筒体与热风炉之间,它可以利用自然风,也可以人造风,然后把风量吹向烘干机的筒体内。管理排风畅销的关键部位是翻板阀和闪动阀,操作好这2个部位,才能保证排风顺利、通风良好。首先我们要学会自行判断通风情况的好与坏。我们用较简单的方式,首先我们把手弄湿,然后把手伸向出料口,这样的话,如果过一会手上的水被蒸发完了,就说明通风良好,否则通风不行,需要调整。当然这只是较简单的也是较有效的判断方法。
  Ensuring the ventilation rate of sand dryer, grasping the temperature in the dryer at any time and adding fuel accordingly can achieve energy-saving drying state. The ventilation area of sand dryer is mainly between the drying barrel and the hot stove. It can use natural or artificial air, and then blow the air into the barrel of the dryer. The key parts to manage the best-selling exhaust air are flip valves and flicker valves. Only when these two parts are properly operated, can the exhaust air be smoothly and well ventilated. First of all, we should learn to judge whether the ventilation is good or bad. We use a simpler way, first we wet our hands, and then extend our hands to the outlet. In this way, if the water on our hands is evaporated in a short time, it means that the ventilation is good, otherwise the ventilation is not good and needs to be adjusted. Of course, this is a relatively simple and effective judgment method.
  通风量的调整我们可以按以下方式进行调试:
  The adjustment of ventilation volume can be adjusted in the following ways:
  1、要注意翻板间漏风倩况,特别是轴承部位的密封情况。并防止翻板阀内掉进来大较矿渣大块、砖头、铁丝等杂物.造成深风,甚至妨碍排料或卡死翻板,不能翻转。
  1. Attention should be paid to the air leakage between the turnboards, especially the sealing of the bearing parts. It also prevents large slag, bricks, wire and other impurities from falling into the turnover valve, which can cause deep wind, even hinder discharging or stuck the turnover plate, and can not be reversed.
  2、观察翻板阀下料较多少及下料间隔大小,是否与污泥烘干机出料速度相适应。翻斗内既不要存料太多影响出料.又不要存料太少振动须繁。
真空烘干机厂家
  2. Observe whether the discharging rate of the turning valve and the discharging interval are suitable for the discharging speed of the sludge dryer. The dumper should not store too much material to affect the discharging, and should not store too little material to vibrate too much.
  3、要按时给转轴油杯加油.每班拧l~2次,银次旋转一扣即可。对闪动阀要观察运转是否灵活,下料是否通畅,平衡锤位置是否得当,三角锥体与下料管口接触是否严密。根据积灰下料情况,可以对平衡锤适当调整。三角锥体通常是活动联接在杠杆上。为了避免闪动因震动而移位,也可在对准下料管口后把它固定焊在杠杆上。
  3. Refuel the oil cup of the rotating shaft on time. Twist it twice per shift and rotate it once. For the flicker valve, it is necessary to observe whether the operation is flexible, whether the blanking is smooth, whether the position of the balance hammer is appropriate, and whether the contact between the triangular cone and the blanking pipe mouth is tight. The balance hammer can be adjusted appropriately according to the condition of ash accumulation. Triangular cones are usually movably connected to levers. In order to avoid flicker displacement due to vibration, it can also be fixed on the lever after aligning the blanking pipe orifice.
  更多有关真空烘干机的相关信息可以点击我们的官网进行咨询:http://www.zhongyanjixie.com
  More information about vacuum dryers can be consulted on our website at http://www.zhongyanjixie.com.
返回顶部

版权所有©山东众焱机械有限公司 备案号:鲁ICP备19005667号-1 服务热线:18005415007 流量统计: