新闻资讯

烘干机减速电机及零部件配备!

2019-03-29 来源:http://www.zhongyanjixie.com 发布人:admin 浏览量:
减速机是烘干机设备中很重要的部件,它可以降低设备的负载惯量,便于设备更好的调速。而且减速机在降速的同时还可以提高输出扭矩,扭矩输出比例是根据电机输出乘减速比,要是扭矩超出减速机额定扭矩,就会在一定程度上影响减速机的使用寿命。
  Reducer is an important part of dryer equipment. It can reduce the inertia of the load of the equipment and facilitate better speed regulation of the equipment. Moreover, the speed reducer can also increase the output torque at the same time. The output ratio of the torque is based on the motor output multiplying and decelerating ratio. If the torque exceeds the rated torque of the reducer, the service life of the reducer will be affected to a certain extent.
  因此选用高质量减速机在烘干机中显得异常重要。减速机的齿轮应该是采用高强度低碳和金刚经渗碳猝火而成的,吃面硬度要达标,齿轮精度高,接触性才会好。传动的效率要高。运转过程要平稳,不能有太大的噪音影响。拆卸检查要方便简单,方便安装。粉煤灰烘干机减速机要求运行平稳,无噪音。
  Therefore, it is very important to select high quality reducer in the dryer. The gear of reducer should be made of high strength, low carbon and quenched by carburizing. The hardness of the eating surface should reach the standard, the gear precision is high, and the contact ability is good. The transmission efficiency should be high. The operation process should be smooth and not be affected by too much noise. The disassembly inspection should be convenient, simple and easy to install. Fly ash dryer reducer requires smooth operation and no noise.
  更换磨损严重的托轮、挡轮或更换轴与轴承,重新校正托轮位置偏差,进行必要的调整,使托轮、挡圈都恢复应有的位置精度与几何精度;现场切削加工轮带表面,检测简体的斜度偏差并做相应的调整,使筒体恢复应有的几何精度。更换大部或全部扬料板,修理或更换窑口密封装置,更换部份通风管道。更换部份磨损严重的传动齿轮、齿轮轴及其轴承,调整其啮合关系。更换磨损的联轴器,装配与调整其配合关系,达到应有的同心度。
  Replacement of worn brackets, retaining wheels or replacement of axles and bearings, re-calibration of the position deviation of brackets, necessary adjustments to restore the position accuracy and geometric accuracy of brackets and retaining rings; on-site cutting and processing of the surface of the wheel belt, detection of the slope deviation of the simplex and corresponding adjustments, so as to restore the geometric accuracy of the cylinder. Replace most or all of the lifting boards, repair or replace the kiln mouth sealing device, and replace part of the ventilation pipeline. Replace some worn transmission gears, gear shafts and bearings, and adjust their meshing relationship. Replace worn coupling, assemble and adjust its coordination relationship to achieve proper concentricity.
真空烘干机厂家
  解体检查减速机,更换磨损严重的齿轮、齿轮轴,更换润滑油与密封零件。更换轮带垫板,重新调整垫板与轮带的径向间隙,达到设计要求的尺寸。更换烧损的耐火砖,炉篦子或看火门,更换损坏的下料管。修理筒体的严重变形,对磨损严重或变形严重的简体进行挖补,对简体较大的弯曲变形进行切割修正。电气设备的检查与修理。
  Dismantling and checking reducer, replacing worn gear and gear shaft, replacing lubricating oil and sealing parts. Replacement of the belt cushion plate and readjustment of the radial clearance between the cushion plate and the belt to meet the design requirements. Replace burnt refractory bricks, grates or fire doors, and replace damaged discharge pipes. Repairing the serious deformation of the cylinder, excavating and repairing the worn or deformed cylinder, cutting and correcting the larger bending deformation of the cylinder. Inspection and repair of electrical equipment.
返回顶部

版权所有©山东众焱机械有限公司 备案号:鲁ICP备19005667号-1 服务热线:18005415007 流量统计: