新闻资讯

烘干机怎么保证高产量的性能?

2019-12-20 来源:http://www.zhongyanjixie.com 发布人:众焱小编 浏览量:
[导读]:  烘干机是处理大量物料的干燥设备。高成品率性能是用户关心的问题之一。近年来,随着节能环保的推广,干燥设备保证了效率和产量。节能的
  烘干机是处理大量物料的干燥设备。高成品率性能是用户关心的问题之一。近年来,随着节能环保的推广,干燥设备保证了效率和产量。节能的方向越来越受到人们的重视,更大程度上减少热损失是其中的一个重要环节。
  The dryer is a drying equipment for handling a large number of materials. High yield performance is one of the concerns of users. In recent years, with the promotion of energy conservation and environmental protection, drying equipment ensures efficiency and output. More and more attention has been paid to the direction of energy saving, and reducing heat loss to a greater extent is an important part of it.
  物料干燥过程中:湿物料通过带式输送机或斗式提升机送至料斗,再由加料管送入给料端。进料管的倾斜度大于物料的自然倾斜度,使物料能够平稳地流入烘干机。烘干机是相对于水平线稍微倾斜的旋转圆筒。物料从相反方向加入,热载体从下侧进入,与物料、热载体、物料同时反向接触流入料筒。当圆筒的旋转材料受重力向下运动时。作为矿物加工行业使用的干燥设备,工业干燥机,我们始终坚持环保节能的路线,让用户感受干燥机的制造商。有关方面,我们可以继续拓展干燥设备市场的市场。
  In the process of material drying: the wet material is sent to the hopper through the belt conveyor or bucket elevator, and then sent to the feeding end through the feeding pipe. The inclination of the feed pipe is greater than the natural inclination of the material, so that the material can flow into the dryer smoothly. The dryer is a rotating cylinder slightly inclined to the horizontal line. The material is added from the opposite direction, the heat carrier enters from the lower side, and simultaneously contacts with the material, the heat carrier and the material in reverse direction and flows into the barrel. When the rotating material of the cylinder moves downward by gravity. As the drying equipment and industrial dryer used in the mineral processing industry, we always adhere to the route of environmental protection and energy saving to let users feel the manufacturer of the dryer. We can continue to expand the market of drying equipment.
  确保烘干机的通风,及时了解烘干机内的温度,并根据燃料情况,实现节能烘干。干燥机通风区主要位于干燥机与热风炉之间。可采用自然风或人工风,将风量吹入烘干机气缸内。阀瓣和闪光阀是排气管理的关键部件。这两个部分运行良好,保证通风顺畅。首先,我们要学会判断通风的质量。用一种更简单的方法,我们先把手弄湿,然后把手伸向出口。如果一段时间后手上的水蒸发了,说明通风良好,否则就是通风不良,需要调整。当然,这是一个更容易辨别的方法。
  Ensure the ventilation of the dryer, know the temperature in the dryer in time, and realize energy-saving drying according to the fuel situation. The dryer ventilation area is mainly located between the dryer and the hot blast furnace. Natural air or artificial air can be used to blow the air volume into the dryer cylinder. Disc and flash valve are key parts of exhaust management. These two parts operate well to ensure smooth ventilation. First of all, we should learn to judge the quality of ventilation. In a simpler way, we first wet our hands and then reach for the exit. If the water on the hand evaporates after a period of time, it means that the ventilation is good, otherwise, the ventilation is poor and needs to be adjusted. Of course, it's a much easier way to tell.
木屑烘干机厂家
  通风调节可调整如下:
  Ventilation regulation can be adjusted as follows:
  1. 注意挡板之间的漏风,特别是轴承部件的密封。防止插入阀落入炉渣、砖头、电线等杂物中。造成风深,甚至阻塞放电或堵塞襟翼,无法翻转。
  1. Pay attention to air leakage between baffles, especially the sealing of bearing parts. Prevent the plug-in valve from falling into slag, bricks, wires and other sundries. Cause wind depth, even blocking discharge or blocking flap, unable to turn over.
  2. 观察切片阀的切割量和下料间隔的大小,是否与污泥干燥机的排出率一致。切勿在倾卸车内存放太多物料,以免影响排放。不要储存太少的振动而使它复杂化。
  2. Observe whether the cutting amount of the slicing valve and the size of the blanking interval are consistent with the discharge rate of the sludge dryer. Do not put too much material in the dump truck to avoid affecting the discharge. Do not store too little vibration to complicate it.
  3.带有油轴的油杯。每班拧1~2次,转动银钥匙。对于闪速阀,检查操作是否灵活,卸载是否平稳,平衡锤定位是否正确,三角锥是否与出料嘴紧密接触。根据灰分沉积情况,可适当调整平衡锤。三角锥体通常铰接在杠杆上。为了避免振动引起的闪蒸位移,也可以在喷嘴对准后将喷嘴固定在杠杆上。
  3. Oil cup with oil shaft. Turn the silver key once or twice per shift. For the flash valve, check whether the operation is flexible, whether the unloading is stable, whether the positioning of the balance weight is correct, and whether the triangle cone is in close contact with the discharge nozzle. The balance weight can be adjusted properly according to the ash deposition. The pyramids are usually hinged on levers. In order to avoid flash displacement caused by vibration, the nozzle can also be fixed on the lever after the nozzle is aligned.
返回顶部

版权所有©山东众焱机械有限公司 备案号:鲁ICP备19005667号-1 服务热线:18005415007 流量统计: