新闻资讯

木屑烘干机厂家燃烧器的清洗和轴承检查!

2019-07-16 来源:http://www.zhongyanjixie.com 发布人:admin 浏览量:
  锯末干燥机在使用前必须经过检查、调整和维护,经验合格后方可投入使用。在每一个阶段的工作结束,锯屑干燥机必须彻底检查,以达到良好的技术条件。让我们跟着一起来看看燃烧器的清洗和轴承检查。
  Sawdust dryer must be inspected, adjusted and maintained before use, and can be put into use only after qualified experience. At the end of each stage, sawdust dryer must be thoroughly inspected to achieve good technical conditions. Let's follow Wantai to see the burner cleaning and bearing inspection.
  定期清洁燃烧器
  Regular cleaning of burners
  燃烧器应定期清洗,如不及时清洗,燃烧器容易着火或发生其他事故。一般烘干机使用3-5次来清除燃烧室表面的灰尘、杂物。另外,要经常检查输送带的三角皮带松紧度是否跑偏,并根据实际情况进行调整。
  The burner should be cleaned regularly. If it is not cleaned in time, the burner is prone to ignition or other accidents. The general dryer uses 3-5 times to remove dust and debris from the combustion chamber surface. In addition, it is necessary to check regularly whether the belt tightness of the triangle belt of the conveyor belt is deviated, and adjust it according to the actual situation.
  检查轴承及其温度
  Check the bearing and its temperature
  烘干机运行过程中需要轴承配合,工作人员应经常检查轴承温度,确保在50℃以内,并检查轴承是否正常。在正常轴承工作时,齿轮的声音应稳定,传动、支架和气缸的转动应无明显冲击、振动和传动。此外,还应根据轴承的使用情况添加润滑油。一般情况下,变速器轴承需要每天加油。电机、减速机及支承轴承应每六个月润滑一次。
  During the operation of the dryer, it is necessary to cooperate with the bearings. Workers should check the temperature of the bearings regularly to ensure that the temperature of the bearings is within 50 C, and check whether the bearings are normal. In normal bearing operation, the sound of gear should be stable, and there should be no obvious impact, vibration and transmission in transmission, bracket and cylinder rotation. In addition, lubricating oil should be added according to the use of bearings. Generally speaking, transmission bearings need to be refueled every day. Motors, reducers and supporting bearings should be lubricated every six months.
  锯末在锯末干燥机滚筒内的运动过程主要取决于锯末自身的状态因素和特性,如锯末的主要重力、给料板与滚筒壁的反作用力、离心力、气举和阻力等。为了提高锯末与热风的接触面积,滚筒内一般都有进给板,使锯末在滚筒内的运动可分为四个阶段。
木屑烘干机厂家
  The movement process of sawdust in the drum of sawdust dryer mainly depends on the state factors and characteristics of sawdust itself, such as the main gravity of sawdust, the reaction force between feed plate and drum wall, centrifugal force, air lift and resistance, etc. In order to improve the contact area between sawdust and hot air, there are generally feeding plates in the drum, so that the movement of sawdust in the drum can be divided into four stages.
  在段中,锯末在给料板的作用下,由滚筒转动起,以匀速圆周运动。第二阶段为锯末匀速圆周运动时,提升机板上的滑动作用与该运动一致。第三阶段是锯末被给料板提升到一定高度,然后从给料板中喷射出来。第四阶段是锯末与滚筒壁接触,相对于滚筒壁滑动,直到锯末落在绞盘上,开始匀速圆周运动。
  In the first section, the sawdust rotates from the drum under the action of the feed plate and moves in a uniform circumference. The second stage is the uniform circular motion of sawdust, and the sliding action on the hoist plate is consistent with the motion. The third stage is that the sawdust is raised to a certain height by the feeding plate, and then sprayed out from the feeding plate. The fourth stage is the contact between the sawdust and the drum wall, sliding relative to the drum wall until the sawdust falls on the winch and starts to move uniformly in a circular motion.
  此外,木屑在滚筒中的停留时间与热风中的热利用率有关。停留时间越长,热利用率越高;停留时间越短,热利用率越低。
  In addition, the residence time of sawdust in the drum is related to the heat utilization rate in hot air. The longer the residence time, the higher the heat utilization rate; the shorter the residence time, the lower the heat utilization rate.
  以上内容由木屑烘干机厂家整理发布,更多相关信息可以点击官网进行咨询:http://www.zhongyanjixie.com
  More information can be consulted by clicking on the official website: http://www.zhongyanjixie.com.
返回顶部

版权所有©山东众焱机械有限公司 备案号:鲁ICP备19005667号-1 服务热线:18005415007 流量统计: